- Are 3.73 gears good for highway?
- What is a 4.11 rear end?
- How much does it cost to get 4.10 gears installed?
- How can you tell if you have 4.10 gears?
- What’s the difference between 4.10 and 4.11 gears?
- Is 3.08 a good gear ratio?
- Is 3.42 or 3.73 better?
- What is the difference between 3.73 and 4.10 gear ratio?
- Are 3.73 gears good for 35 tires?
- Which gear ratio is faster?
- Are short gears better than long gears?
- What does a 4 11 gear ratio mean?
- How many teeth does 4.11 gears have?
- Are 4.10 gears good for highway?
- Are 3.73 or 4.10 gears better?
- What are 4.11 gears good for?
- Is 3.55 or 3.73 gears better?
- Are 4.10 gears good for 35s?
- Do gears make car faster?
- Which rear end gear ratio is best?
- WHAT WILL 4.10 gears do?

## Are 3.73 gears good for highway?

Rear end gears (2.79’s, 3.00’s, 3.25’s, etc) are great for freeway driving, bit not good for 0-60 MPH or accelerating from a dead stop.

Shorter gears (higher numbers) are much better suited for accelerating, such as 3.55, 3.73, 3.91’s, 4.11’s etc.

Always remember, for very “give” there is a “take”..

## What is a 4.11 rear end?

A 4.11 refers to a 4.11:1 ratio. This means that the driveshaft turns 4.11 times for each time the axles turn once. This yields strong acceleration but, depending on transmission ratios, can mean the car cruises at high RPMs.

## How much does it cost to get 4.10 gears installed?

Installation costs will vary, but a good rule of thumb is between $250 and $300. Be sure to work with a reliable shop that you trust for installations. You can also save money on your installation labor by having your Trac-Lok rebuilt at the same time as your gears are installed, see drop down option above.

## How can you tell if you have 4.10 gears?

Jack the car up on jack stands, mark the driveshaft with chalk or a marker. Put car in N and slowly spin the tire 1 full turn while counting how many times the mark on the driveshaft goes around. 4+ a little more is 4.10 gears.

## What’s the difference between 4.10 and 4.11 gears?

Adventurer. 4.10 will have 41/10 teeth so more, but smaller for the same diameter ring. 4.11 will have 37/9 teeth which will be larger. The 4.10 is a stronger pinion.

## Is 3.08 a good gear ratio?

Yes, you are exactly right, towing with a 6 speed with 3.08s is still better than towing with a 4 speed and 3.73s. If its a heavy trailer, you will probably never use 5th and 6th gears, but who cares? crank turns to rotate the rear wheels once that counts.

## Is 3.42 or 3.73 better?

3.73 is 9% higher than 3.42. That means your RPMs at any given speed will be 9% higher. You should be able to accelerate about 9% faster, in the lower gears at least. Your maximum speed in each gear will decrease by 9%.

## What is the difference between 3.73 and 4.10 gear ratio?

A 3.73 is a higher gear ratio for half ton pickups its not the best gear for pulling trailers, now the 4.10 gears come stock from the factory on newer trucks and is one of the best rear end gears to use if you plan on pulling a trailer. These both vary by fuel mileage consumption so choose wisely.

## Are 3.73 gears good for 35 tires?

You will be fine. Just gonna lose mpg and slow your truck down. I have run 35s with 3.73s and no issues at all. In fact, my recent Plat had a 4-inch lift, heavy 34.5 inch Nitto Trails, and 3.55 gears, and ran great!

## Which gear ratio is faster?

A lower (taller) gear ratio provides a higher top speed, and a higher (shorter) gear ratio provides faster acceleration. . Besides the gears in the transmission, there is also a gear in the rear differential.

## Are short gears better than long gears?

Close vs Wide ratios Closer gears also means better fuel economy since the engine can be kept in its optimal RPM zone for fuel consumption. However, having closer ratios either makes the highest gear too short or makes the 1st gear too long, both of which can be undesireable (see earlier).

## What does a 4 11 gear ratio mean?

4.11 is a gear ratio.. basically it means that the the pinion or driveshaft will turn 4.11 times for each rotation of the tires. The higher the ratio, the more times the the the engine, transmission, transfer case, etc turns to make the wheels spin which yields less top speed but more low end torque (usually).

## How many teeth does 4.11 gears have?

Example: 4.09 / 4.10 / 4.11 Gear RatiosAxleRing Gear TeethFinal RatioToyota 8″374.11Dana 44454.09Dana 60414.10GM 10.5″ 14 Bolt454.096 more rows

## Are 4.10 gears good for highway?

Installing 4.10 gears improves the car’s performance on the track but with negligible effects to the highway driving. … Switching from a gear set of 3.55 or 3.73 to 4.10 gears will affect your gas mileage slightly as your engine will be turning more times to rotate the rear wheels once.

## Are 3.73 or 4.10 gears better?

The difference between a 3.73 vs 4.10 gear ratio can cause many questions for the automotive enthusiast….3.73 VS 4.10 Ratio.3.73 Ratio4.10 RatioNot as fast off of the lineQuicker Off The LineLower TorqueHigher TorqueBetter Gas MileageDecreased Gas MileageHigher Top SpeedLower Top SpeedMar 3, 2021

## What are 4.11 gears good for?

4.11:1 is a “lower” gear ratio, meaning you have more torque, lower top speed, and you will generally consume more fuel. Usually people put 4.11:1 gears in trucks to be used off-road for the extra torque and the better “crawling” capabilities.

## Is 3.55 or 3.73 gears better?

3.55 will give you a little better gas mileage on the highway and slightly more highway oriented performance. 3.73 may be better for towing, lower end power (off the line acceleration), and may result in worse gas mileage on the highway.

## Are 4.10 gears good for 35s?

Yes, I’m running 35s on stock 4.10s here, with auto tray. It’s fine.

## Do gears make car faster?

The simple answer is yes. More aggressive gearing creates a quicker car but not a faster car. A gearing change will have a noticeable affect on your car. If you swap in taller rear gears, you can gain some top-end speed, making your car faster, but you’re going to be a bit slower leaving from a stop.

## Which rear end gear ratio is best?

3:55The most popular rear end ratio in trucks today is the 3:55, which sort of averages towing power and fuel economy. This is a good ratio for the occasional towing or hauling individual. For a person who tows more often, and heavier loads, the 3:73 or 4:10 may be more appropriate.

## WHAT WILL 4.10 gears do?

A 4.10 axle ratio will provide improved acceleration in stop and go city traffic. A lower gear (higher numerical) ratio provides more low-speed wheel torque, which makes it easier to get the vehicle moving when pulling a trailer or carrying a heavy load.