- What is the starting current of 1 hp motor?
- How do you size a 12v fuse?
- How many watts is a 1 hp motor?
- How many amps does a 5 hp compressor draw?
- How many amps does a 3 HP motor draw?
- What size breaker do I need for a 5 hp motor?
- What size wire do I need for a 1 hp motor?
- How much HP does a drill have?
- How do you measure a 3-phase breaker?
- What size breaker do I need for a 3 phase motor?
- How do I know what size motor breaker I need?
- How many HP is 15 amps?
- How many amps is a 3 phase 5HP motor?
- How many amps is a 1hp motor?
- What size breaker do I need for a 75 hp motor?
- What size breaker do I need for a 7.5 HP 3 phase motor?
- How do I convert HP to amps?
- What size breaker do I need for a 2 hp motor?

## What is the starting current of 1 hp motor?

For single phase motors, NEC table 430-148 gives 230 Vac full load current of 8 amps for a 1 HP motor.

Note, that a 1 HP motor not fully loaded (good practice) will show current draw of less than 8 amps..

## How do you size a 12v fuse?

Find the size of fuse by multiplying the amps required by the device (2) by 1.5. 2×1.25 = 2.5 then we will round up to the nearest fuse size (in multiples of 5 amps) which would call for a 5 amp fuse. Cross Reference that fuse size to verify that it’s below the Maximum fuse size called out by this chart.

## How many watts is a 1 hp motor?

746 wattsOne electric horsepower is equal to exactly 746 watts.

## How many amps does a 5 hp compressor draw?

21 ampsA 5 hp will be around 21 amps, and a 7.5 hp will be around 35 amps.

## How many amps does a 3 HP motor draw?

AC Motor Full Load AmperesHP200 Volts440-480 Volts14.82.11.56.93.027.83.43114.823 more rows

## What size breaker do I need for a 5 hp motor?

therefore, 7 A circuit breaker will be a IDEAL choice for a 5 HP motor with above parameters of the motor.

## What size wire do I need for a 1 hp motor?

Single Phase (230 Volt) – Wire Size Selection Guide*HPCable Length114121 1/21412214124 more rows

## How much HP does a drill have?

A wide range of electric drills are available with more or less power (one-half horsepower is about average) and with various maximum speeds (most models top out at between twelve hundred and twenty-five hundred revolutions per minute).

## How do you measure a 3-phase breaker?

For 3-phase loads, you divide the VA by the nominal voltage and by the square root of three (approximately 1.732). If your total 3-phase load in a 480V system is 50,000VA, what size breaker do you need? 50,000VA ÷ (480V × 1.732) = 60.2A. The next size up is 70A.

## What size breaker do I need for a 3 phase motor?

Full Load Current: Three Phase AC MotorsMotor HorsepowerSize Breaker10230V 460V50 3015230V 460V70 4020230V 460V100 5025230V 460V100 506 more rows•Feb 16, 2017

## How do I know what size motor breaker I need?

You must size the conductors at 125% of the motor FLC [430.22(A)]. You must size the overloads no more than 115% to 125% of the motor nameplate current rating, depending on the conditions [430.32(A)(1)]. You must size the short-circuit ground-fault protection device from 150% to 300% of the motor FLC [Table 430.52].

## How many HP is 15 amps?

2.17 HPCommon Amps to Horsepower ConversionsAmpsHorsepowerEfficiency10 A1.45 HP90%15 A2.17 HP90%20 A2.9 HP90%25 A3.62 HP90%10 more rows

## How many amps is a 3 phase 5HP motor?

These are only intended to be guidelines and in all cases the full load amps of the motor nameplate should be used for final calculations….Here are the Full Load Amp (FLA) values for typical 230VAC and 480VAC 3 phase motors.Motor horsepowerFull load amps 230VACFull load amps 460VAC394.55157.57.5221110271417 more rows•Apr 1, 2017

## How many amps is a 1hp motor?

AMP DRAW BASED ON HORSEPOWERHP1 Phase Amps3 Phase Amps115 volt230 volt1164.21-1/22062246.812 more rows•May 21, 2020

## What size breaker do I need for a 75 hp motor?

Registered. micromind said: The code minimum CU wire size for a 75HP 3ø motor operating at 480 volts is #1. The code maximum breaker size for said motor is 225 amp.

## What size breaker do I need for a 7.5 HP 3 phase motor?

Re: Wire and breaker size for 7.5 hp motor You need 50 amp rated wire with a 50-100 amp breaker.

## How do I convert HP to amps?

Converting horsepower to amps can be done in a few simple steps, or using this simple formula.Amps = (Horsepower × 746) ÷ Efficiency ÷ Volts.Watts = Horsepower × 746.Watts = WattsηAmps = Watts ÷ Volts.Amps = HP × 746V × η × PF.

## What size breaker do I need for a 2 hp motor?

How to Calculate How What Size Circuit Breaker a Machine will Need:HorsePower of Main Motor220 Volts, 1 phase220 Volts, 3 phase1 Hp5.6 Amps2.8211.25.6316.88.4422.411.211 more rows